Can lanthanum doping enhance catalytic performance of silver in direct propylene epoxidation over NaMoAg/SiO_2?

In the attempt to reduce surface free energy of silica to improve interaction of silica with silver, silica was doped by different amounts of low surface energy lanthanum, La_2O_3, through impregnation. The doped and undoped silica were used as supports for preparation of Na/Ag/Mo/La_2O_3-SiO_2 catalysts. Catalytic performances of the catalysts were evaluated in direct epoxidation of propylene(DPO) using molecular oxygen under atmospheric pressure and without adding hydrogen. Adding 5 wt%La to the Na/Ag/Mo/SiO_2 catalyst improves both the catalysts electivity in DPO and its stability over 20h of time-on-stream.The characterization results show that La_2O_3 species interact strongly with silver particles on the silica surface which result in significant improvement in the dispersion profile of silver and marked decrease in the size of silver nanoparticles(AgNPs). The estimated mean diameter of AgNPs is ca. 4.0 nm in Na/Ag/Mo/5 wt%La_2O_3-SiO_2, which is smaller than that(53.9 nm) found in Na/Ag/SiO_2. The presence of subnanometer AgNPs on Ag/La_2O_3-SiO_2 prior addition of MoO_3 and NaCl to the sample can enhance the mutual electronic synergism between Ag, MoO_3 and Na for selective production of propylene oxide.     

塔里木盆地中秋1凝析气藏成藏条件及演化过程

2018年12月,塔里木盆地秋里塔格构造带天然气勘探取得重大突破,中秋1井在下白垩统巴什基奇克组测试获高产工业气流,发现了该构造带迄今为止最大的整装凝析气藏。为了给该构造带下一步油气勘探部署提供依据,在充分利用前人研究成果的基础上,基于岩心、薄片、测井及地球化学分析资料,明确了中秋1大型凝析气藏的油气藏特征和气藏类型,分析了该气藏天然气成藏条件并推演其演化过程。研究结果表明:①中秋1大型气藏属于低含凝析油凝析气藏,天然气为煤成气,主要来自区内侏罗系腐殖型煤系烃源岩;②该构造带能够形成大型油气藏的有利地质条件是三叠系和侏罗系发育的两套巨厚高演化烃源岩、白垩系发育的大型辫状河三角洲规模有效砂岩储层、喜马拉雅晚期以来的构造活动形成的大规模楔状叠瓦构造圈闭、古近系和新近系巨厚膏盐岩形成的优越保存条件,以及油气生成与圈闭形成的良好时空匹配;③该气藏具有先油后气、晚期快速气侵聚集成藏的成藏模式,总体上是一个"早期聚油、晚期气侵、改造调整、快速成藏"的成藏过程。结论认为,该构造带油气成藏条件优越,具有广阔的油气勘探前景。     

柴达木盆地三湖坳陷横波勘探中的低幅异常消除技术

近年来,在柴达木盆地三湖坳陷开展了横波地震勘探,但是由于该区低幅度构造发育,横波静校正引起的"低幅"异常与上述低幅度构造相互混杂,难以区分。为此,针对该区横波表层调查难以控制表层横波速度模型的变化、横波近偏移距初至污染严重、横波折射层发育导致高速界面难以确定等问题,首先采用曲线拟合技术预测污染区横波初至时间确保初至完整性,然后采用面波模型与多层折射分层联合约束反演横波表层速度,最后通过基于速度谱分析的层位匹配建模技术确定合理的横波速度界面,形成了横波表层"低幅"异常消除技术,并进行了现场应用及效果评价。研究结果表明:①曲线拟合技术可以弥补近道污染区横波初至空白,保证层析反演模型的完整性;②基于瑞雷波的频散特性反演建模可以为确定该区浅层横波速度提供可靠的资料,提高浅层模型精度;③面波模型与多层折射分层联合约束反演能够更准确的反演该区表层横波速度场,较好地建立横波速度模型,消除横波剖面上"低幅"异常现象。结论认为,所形成的横波地震勘探低幅异常消除技术消除了横波静校正引起的"低幅"异常现象,提高了横波地震资料的成像品质。     

废脱硫剂在铁矿烧结中的应用

钢厂煤气脱硫工序排放的废脱硫剂是一种难以利用的有害固体废弃物，含一定量的铁及较高的钙和硫等元素。对废脱硫剂配入铁矿粉中进行了烧结杯的试验研究，结果表明，当废脱硫剂配比超过01%后，随着废脱硫剂配比的升高，烧结矿转鼓强度下降，利用系数下降，烧结烟气中SO2与NOx浓度增加，烧结矿的还原度有所下降，但烧结矿的低温还原粉化性能有所改善。烧结矿的矿相研究发现，废脱硫剂配比偏大时，磁铁矿体积分数增大，铁酸钙体积分数减少，并由针状结构向柱状、板状演变，烧结矿的气孔率上升。主要原因在于其粒度偏粗，含硫高，不利于成矿。当废脱硫剂粒度为-63mm及其配比控制在01%时，烧结矿的产量和质量有所改善，烟气中SO2、NOx较基准试验变化不大。工业试验表明，在烧结混匀矿中配入废脱硫剂配比小于012%时，烧结矿产量和质量没有明显变化，烧结烟气脱硫脱硝效果也没有受到影响。废脱硫剂掺入铁矿中进行烧结是一种资源化利用的有效方法，不仅解决了有害固体废弃物对环境的影响，而且使二次资源得到综合利用。     

基于ATP-ABE的访问控制方案

对访问控制机制中存在的安全性和有效性的问题进行了研究，提出了基于访问树剪枝的属性加密ATP-ABE（Access Tree Pruning Attribute Based Encryption）的访问控制方案。当ATP-ABE算法需要访问它的树型结构访问策略时，通过剪枝处理访问树结构中包含用户ID属性节点的分支，提高了用户所有者DO（Data Owner）管理和控制属性的效率，更加有效地实现了数据共享。还为访问树结构设计了许可访问属性，使DO仍保留共享数据的关键属性，并且能够完全控制它们的共享数据。基于决策双线性密钥交换算法DBDH（Decisional Bilinear Diffie-Hellman）假设分析了ATP-ABE方案的安全性，研究结果表明与两种经典ABE方案比较，ATP-ABE更加有效地减少了算法的系统设置、私钥生成、密文大小、用户属性撤销以及加解密过程中的计算开销，并给出了定量结论。     

车辆自组织网络中新型NP-CSMA随机多址协议研究分析

智能交通的出现使得车辆自组织网络受到越来越多的关注。车辆自组织网络的动态拓扑结构变化非常剧烈,这对网络的吞吐率、传输速率等性能提出了很高的要求。提出1种具有握手机制协议的自适应多通道双时钟NP-CSMA随机多址接入协议。该协议首先区分2种P-CSMA协议,握手机制成功解决了隐藏的终端问题,双时钟机制减少了平均空闲时间,多通道机制增加通道数量和划分用户优先级的同时提高了系统吞吐率,自适应机制能够使系统在高负载下保持稳定吞吐率。还对该协议的传输速率进行了分析,得出该协议的传输速率相对较高的结论。通过平均周期方法推导吞吐率和传输速率的计算公式,仿真结果与理论推导一致。     

Reaction synthesis of spark plasma sintered MoSi2-B4C coatings for oxidation protection of Nb alloy

MoSi₂-B₄C coatings with different B₄C contents were prepared on Nb alloy by spark plasma sintering (SPS) process. Powder mixtures of Mo, Si and B₄C were used as the coating starting materials. Besides MoSi₂ and B₄C phases, small amounts of SiC and MoB are also found in the coatings because of the reactions of Mo, Si and B₄C powders during sintering. Compared with single MoSi₂ coating, the MoSi₂-B₄C coatings show better oxidation resistance at 1450?℃, and dense B₂O₃-SiO₂ oxide scales form after 100?h oxidation. The B₄C or MoB in the MoSi₂-B₄C coatings can serve as the B donor for the formation of B₂O₃. A slight degradation in the microstructure of the MoSi₂-B₄C coatings after oxidation is observed, which can be attributed to the presence of an NbB layer in the inter-diffusion zone of the coatings that retards the inward diffusion of Si from the coating into the substrate alloy. The microstructure development and oxidation behavior of the MoSi₂-B₄C coatings have been discussed.     

基于改进雷达图的配电系统电能质量评估方法

本文针对配电系统电能质量综合评估存在的评估指标权重分配过于主观或客观的问题,提出一种基于改进雷达图法的配电系统电能质量评估方法。该方法利用最小偏差组合权重法计算各评估指标的最优组合权重。并在传统雷达图的基础上对各指标轴间夹角值的确定和特征向量的选取两方面做了进一步的改进。首先采用扇形区域取代原始的三角形区域,并利用最小偏差组合权重法计算各指标轴间夹角值。其次选择新的特征向量构造评估函数对配电系统电能质量进行综合评估。最后通过对某钢铁厂棒材变电站10kV配电系统电能质量进行综合评估,验证了该方法的可行性和合理性。较传统雷达图而言,改进雷达图法解决了传统雷达图法中各指标间信息共用以及评估结果不唯一的问题,使评估结果更加准确合理。     

Effects of temperature on creepage discharge characteristics in oil-impregnated pressboard insulation under combined AC–DC voltage

Due to the complexity of the valve side winding voltage of the converter transformer, the insulation characteristics of the oil-impregnated pressboard (OIP) of the converter transformer are different from those of the traditional AC transformer. The study on effect of temperature on the creeping discharge characteristics of OIP under combined AC–DC voltage is seriously inadequate. Therefore, this paper investigates the characteristics of OIP creepage discharge under combined AC–DC voltage and discusses the influence of temperature on creepage discharge characteristics under different temperatures from 70°C to 110 °C. The experimental results show that the partial discharge inception voltage and flashover voltage decrease with increasing temperature. The times of low amplitude discharge (LAD) decrease and amplitude of LAD increases. Simultaneously, the times of high amplitude discharge (HAD) gradually increase at each stage of creepage discharge with higher temperature. The analysis indicates that the charge carriers easily accumulate and quickly migrate directional movement along the electric field ahead of discharging. The residual charge carriers are more easily dissipated after discharging. The ‘hump’ region of LAD moves to the direction of higher discharge magnitude. The interval time between two continuous discharges is shortened obviously. The concentration of HAD accelerates the development of OIP insulation creepage discharge. The temperature had an accelerating effect on the development of discharge in the OIP under applying voltage.     

板栗壳黄酮结构分析及其对胰脂肪酶活力的抑制作用

在分析板栗壳黄酮结构的基础上，研究其对胰脂肪酶的抑制作用及类型。采用醇提法提取板栗壳中的黄酮，并用AB-8大孔吸附树脂进行纯化，冻干后得到的黄酮含量为（107.50±1.00）mg/g，提取得率为（5.66±0.05）%。利用超高效液相色谱-四极杆/静电场轨道阱质谱联用技术对板栗壳黄酮进行结构分析，鉴定出8 种黄酮类化合物。采用对硝基苯酚法测定胰脂肪酶活力，分别考察板栗壳黄酮对胰脂肪酶的抑制效果及不同反应条件下板栗壳黄酮对胰脂肪酶活性的影响，结果表明，板栗壳黄酮对胰脂肪酶有较好的抑制作用，半抑制浓度（half maximal inhibitory concentration，IC50）为0.074 mg/mL，且使胰脂肪酶最适pH值向碱性偏移。通过Lineweaver-Burk双倒数作图法确定其抑制类型为非竞争性抑制，抑制常数Ki＝53.19 mg/mL。由此可见，板栗壳黄酮是一种效果良好的胰脂肪酶抑制剂。